铁路旅客旅行换乘方案优选算法

为给铁路旅客选择合理的旅行方案提供参考,以旅行目标值与换乘目标值之和最小作为目标函数值,考虑旅客从起点站出发、最终到达终到站、在中转站进出平衡的约束条件,建立旅客旅行换乘方案选择问题的数学模型。分别给出旅行时间、换乘次数、票价、距离、到发时刻和综合指数6种目标权值的确定方法,提出最短路法和列车匹配法2种求解方法。最短路法是通过构造并简化旅客运输网络,求出网络上若干条次短路,再根据各条次短路上列车的接续,构造列车换乘方案网络图,根据该网络的目标权值确定最短路,得到最优换乘方案。列车匹配法是根据列车运行图信息直接搜索发、到站的接续列车集合,求其两列车对应的重合停车站,根据重合停车站集合的情况选择迭代步数,剔除显然不利方案,构成换乘方案,根据方案的权值进行比选,得到最优换乘方案。对2种算法均用C#编程实现,并用现有的全路客票数据进行检算。计算结果表明:2种算法均能得到最优换乘方案;列车匹配法所用计算时间比最短路法少160 ms。     

机车出租效益论证计算方法的探讨

根据机车出租收费标准,讲述了机车出租效益论证计算的基本原则,由此确定出效益计算的基本流程和基本方法,并以计算工作底稿实例加以说明,最后提出尚存在的问题和改进建议。     

Thermal design of automobile exhaust based thermoelectric generators: Objectives and challenges

The potential for thermoelectric power generation (via waste heat recovery onboard automobiles) to displace alternators and/or provide additional charging to a vehicle battery pack has increased with recent advances in thermoelectric material processing. In gasoline fueled vehicles (GFVs), about 40% of fuel energy is wasted in exhaust heat, while a smaller amount of energy (30%) is ejected through the engine coolant. Therefore, exhaust-based thermoelectric generators (ETEG) have been a focus for GFV applications since the late 1980s. The conversion efficiency of modern thermoelectric materials has increased more than three-fold in the last two decades; however, disputes as to the thermal design of ETEG systems has kept their overall efficiency at limited and insufficient values. There are many challenges in the thermal design of ETEG systems, such as increasing the efficiency of the heat exchangers (hot box and cold plate), maintaining a sufficient temperature difference across the thermoelectric modules during different operating conditions, and reducing thermal losses through the system as a whole. This paper focuses on a review of the main aspects of thermal design of ETEG systems through various investigations performed over the past twenty years. This paper is organized as follows: first, the construction of a typical ETEG is described. The heat balance and efficiency of ETEG are then discussed. Then, the third section of this paper emphasizes the main objectives and challenges for designing efficient ETEG systems. Finally, a review of ETEG research activities over the last twenty years is presented to focus on methods used by the research community to address such challenges.     

Lane-following method for high speed autonomous vehicles

This paper presents a steering control method for lane-following in a vehicle using an image sensor. With each image frame acquired from the sensor, the steering control method determines target position and direction, and constructs a travel path from the current position to the target position either as an Arc-path or S-path. The steering angle is calculated from the travel path thus generated, and the vehicle follows the travel path via motor-control. The method was tested using a vehicle dubbed as KAV (Korea Autonomous Vehicle) along an expressway (Seoul Inner Beltway) trajectory with a variety of radii (50 m ∼ 300 m) while traveling at a speed of 60 km/h to 80 km/h. Compared with an experienced human driver, the method showed little much difference in performance in terms of lane-center deviation. The proposed method is currently employed for high speed autonomous driving as well as for stop and go traffic.     

基于支持向量机的发动机气路故障预诊断

为实现航空发动机气路故障在线预诊断,分析了地空数据链系统中发动机气路参数报文的协议格式,建立了基于支持向量机算法的发动机气路参数在线预测模型。以便携式地空数据链收发系统为硬件基础,构建发动机报文并行处理系统,获取建模所需的训练样本。利用最终误差预报准则确定样本数据嵌入维数,实现时序样本数据的相空间重构。提出自适应网格搜索法优化支持向量机建模参数,获得气路参数在线预测模型,与航路飞机建立地空数据链通信,预测气路参数趋势。预测结果表明:参数低压转子转速、高压转子转速、尾气温度与燃油流量的相对预测误差分别为2.5%、2.1%、1.9%与2.3%,因此,支持向量机模型具有较高预测精度。     

基于摄像头的路径识别智能车控制系统设计

介绍一种基于CCD摄像头的路径识别的智能车控制系统,设计了硬件结构与方案,提出了转向机构的控制策略,该智能车能准确实现自主寻迹,具备抗干扰性极强,稳态误差小等特点。     

重型卡车驾驶室振动传递函数分析和优化

试验测试和分析表明,驾驶室地板振动不仅会导致座椅振动,恶化驾乘舒适性,并且会产生噪声,影响车辆的NVH性能。本文对驾驶室地板的振动进行了分析,计算了某重卡驾驶室地板的传递路径响应和模态贡献量,并与试验测试结果进行了对比。基于经过校核的仿真模型,对驾驶室地板结构进行了优化,提供了改进方案。对改进方案的分析显示,在发动机怠速激励频率下,座椅导轨的振动加速度峰值降低了3.1dB,NVH性能获得了显著的改善。     

基于模糊神经网络的智能车辆循迹控制

为提高智能车辆自主循迹控制的精度,提出了一种基于模糊神经网络控制( FNNC)和神经网络预测( NNP)的智能循迹控制策略。转向控制器的输入量有3个：预瞄点处的横向循迹误差、汽车横摆角速度和侧向加速度。车速控制器的输入量有4个：预瞄点处的面积误差、侧向加速度、汽车侧偏角和转向盘转角。网络训练采用误差反向传播法。仿真与试验结果表明,所设计的循迹控制器通过对驾驶员操作样本的训练,能实现对车辆的车速与转向控制,横向循迹误差和目标车速均比较理想。     

基于多目标优化的兴趣点指路标志布设模型

在指路标志的工程应用中,常要为兴趣点规划一条布设指路标志的指引路径.首先,基于道路网络的拓扑表达,考虑指引路径的长度、交通量和设置指路标志的数量,定义了衡量指引路径优劣的多目标搜索路径度量值.其次,以网络分析为基础,建立了搜寻最优指引路径的模型,从给定入口开始,以广度搜索算法在路网上搜索,并动态更新搜索路径的度量值,直至获取优化的指引路径.最后,以广州大学城为试验区域,利用上述模型计算得到了从南沙港快线出口到中山大学的指路标志布设的规划路径.对比规划路径与最短路径的多目标优化度量值表明:规划路径兼顾了布设路径的便捷性和指路标志牌布设成本的特点,模型是可行有效的.     

基于手机信令数据的游客识别与出行轨迹匹配方法

为统计旅游交通的客运量，分析公路交通运输需求，优化运输组织，合理构建“快进慢游”综合交通旅游网络，研究提出基于手机信令数据的游客识别与出行轨迹匹配方法。通过划定景区边界，设置停留时间阈值，识别手机用户的游客身份；同时，借助地图工具批量计算信令发生位置间的出行路线与行程时间，匹配实际公路网。实例分析结果表明，手机信令数据能呈现手机用户的出行轨迹，且信令数据的位置轨迹与公路线位走向结合密切。在人们越来越依赖地图导航软件规划出行路径的背景下，利用该方法能更准确地识别景区游客并估计游客往来景区的出行路径。